[Dan]

hi all, to answer some of the questions…

I’m running left and right out of the scarlett 2i2 into an amp which is more like a general music amp (my wife uses it for her dance school with the speakers I’m using and it sounds fine when she runs a laptop or similar through it).

Amp doesn’t have any eq on it at all, just left and right volume.

I’m using headphones from the scarlett 2i2 and the sound is great.

many thanks,

Dan

[Dan]

many thanks Shootie – it was as simple as enabling the loopback as you suggested!

 

[Dan]

I tried downloading Focusrite Control 2, but it says it’s not compatible with my 4i4 (Gen 3) device.

Scarlett 4i4 setup:

Only USB from PC and headphones – nothing in the 2 mic/instrument inputs

here’s the control screenshot: https://ibb.co/JWvhKBWC

EZD3 settings: https://ibb.co/Q7g93z5C

• The post has been modified 2 times, last modified 3 months ago by Dan.

[Dan]

hi all,

still not working for me in OBS… here’s where i’m at…

1. Windows (10) Sound Output: Speakers (Focusrite USB Audio).
2. Windows (10) Sound Input: Analogue 1 + 2 (Focusrite USB Audio).
3. Scarlett 4i4 Monitor Outputs: “Playback 1-2”
4. Scarlett 4i4 Line Outputs 3-4: “Playback 1+2”
5. Scarlett 4i4 loopback enabled as “Playback 1-2” (and unmuted).
   – Note: i can see all levels moving on all the above (in the Focusrite Control Panel) when i play EZD3
6. OBS – i’ve cleared all ‘scenes’ and ‘sources’
7. OBS – created new Scene called “EZDrummer 3”
8. OBS – created a new source called “Drums” with the following settings:
   1. Device: Focusrite USB ASIO
   2. Format: Stereo
   3. OBS Channel 1: empty (no selection available in the dropdown)
   4. OBS Channel 2: empty (no selection available in the dropdown)

I can hear audio from youtube in OBS, but nothing still from EZD3 – i must be doing something wrong here.

Operating system: Windows 10

[Dan]

thanks everyone, i’ll give those a go tomorrow

[Dan]

thanks everyone, much appreciated.

[Dan]

i checked out the video (is that you btw?), but I’m still unsure on how to physically connect everything up.

• TD-27 to PC or USB Audio Interface (by which type of cable, midi or USB?)
• PC speaker output to USB Audio Interface.
• Headphones in the USB Audio interface.
• Do I just run Reaper or youtube as normal once connected?

[Dan]

Thanks again Shootie – i think i said already, i am using Reaper so i can drop mp3s in and jam, but only if I select poor-performing audio settings where I get latency and/or distortion.

I’ll look at scarlett 2i2.

Dan

 

[Dan]

Thanks for this Doug.

if i use an audio interface, will that enable me to hear sound from youtube or Reaper and EZD3 without the noise or lag?

I’ve never set anything like this up before and I can’t find any decent info on how to do it all.

thanks in advance.

[Dan]

hey Shootie, thanks for getting back so quickly.

I’ve connected TD-27 to an old desktop – it’s an old but decent spec (16gb RAM, i7, 1070 GFX etc).

I’m running EXDrummer into Reaper already.

I’ve lowered the buffer as low as it will go on each working option in the ‘output’ list (ASIO doesn’t work for example).

so, final outcomes are:

1. exclusive on audio out on EZDrummer = no latency, but no other sound available from any other software.
2. any other audio option on EZDrummer = latency and/or distorted sound, but sound is available from the other software (like Repaer).

[Dan]

i have a similar problem, but i want to route the sound back to my TD-27 so I can hear it on the headphones connected to the TD-27… is this possible?

 

Operating system: Windows 10

[Author]

Replies