Topic: Removing bleed from OHs

Viewing 8 replies - 1 through 8 (of 8 total)

Replied September 13, 2023 at 20:52 #3133128

Shootie
Participant

Depending on which preset you use, you can find some worthy bleed controls. Of course routing out a non-Orignal Mix Preset may not retain the tone of the preset. There’s give and take with all options here.

I think with your expectations, crossgrading to Superior Drummer is the only option for ultimate bleed control. I hope a TT mode will correct me if I’m wrong.

EZD3 Tutorials | EZBass Tutorials | Toontrack themed FB Group | Toontrack themed Discord Group

Replied September 13, 2023 at 21:09 #3133137

akabusker
Participant

Studio one user here. Are you using Artist or Professional?

Do you have multi-output set up in Ezdrummer so that there’s individual tracks in the vst instrument window?

If so, does your mixer in Studio One showing corresponding tracks to the Ezdrummer set-up?

Are you mixing your drums to a bus? If so do you have Mix FX enabled on the Drum Bus? If so switch it off.

There’s some other settings like listen thru bus you might want to switch off.

EZdrummer version: 3.0.6
Operating system: Windows 10

Replied September 13, 2023 at 21:23 #3133141

kibepuravik
Participant

Shootie wrote:

I think with your expectations, crossgrading to Superior Drummer is the only option for ultimate bleed control. I hope a TT mode will correct me if I’m wrong.

Are you serious? Why have routing options in EZD3 at all then? Crossgrading to Superior Drummer just to get isolated drum samples seems a little overkill to me. It just seems incredibly limiting for no reason.

akabusker wrote:

Studio one user here. Are you using Artist or Professional? Do you have multi-output set up in Ezdrummer so that there’s individual tracks in the vst instrument window? If so, does your mixer in Studio One showing corresponding tracks to the Ezdrummer set-up? Are you mixing your drums to a bus? If so do you have Mix FX enabled on the Drum Bus? If so switch it off. There’s some other settings like listen thru bus you might want to switch off.

I’m using the latest version of Studio One 6 Artist. I’ve set up stereo multichannel routing through EZD3 for kick-in, snare top, hi-hat, rack toms, floor toms, OH (including ride) and amb respectively. I’ve also created separate tracks for each of the routed channels in the Studio One instrument tab on the left side of the mixer. Each of the channels in EZD3 is routed to a separate track, which I can mute and solo as needed. All of the drum sounds are isolated as expected, all except the OH channel, which is what’s left me scratching my head. I’m not using any bus channels in this case and Studio One 6 Artist doesn’t even have Mix FX.

Replied September 14, 2023 at 16:35 #3133380

akabusker
Participant

Hi. I tried to install S1 artist last night to check out this issue you are having. Unfortunately my computer wouldn’t let me use the Artist version alongside the Professional version.

You’re right about mix fx – which is why my first question was which version of S1 you were using. Unfortunately I have to mess around with my system to test this out which might take a further day.

Replied June 29, 2024 at 16:07 #3266427

shureak
Participant

Same issue with Ableton and EZD3. OH has bleed from all other drums, I want have an option to remove that bleed to get clean Cymbals track without any bleed. Please help

EZdrummer version: 3.0.6
Operating system: macOS Sonoma (14)

Replied June 29, 2024 at 16:23 #3266433

John
Moderator

Well,
you could always start from a Preset that has an OH Bleed Knob (or more) on the Mixer page , like e.g. most of the Michael Ilbert Main Room presets, and then remove the Bleed and switch out kit pieces if needed.
If you come up with something you like, you save it as your own User Preset.

BR,
John

John Rammelt - Toontrack
Technical Advisor

Replied June 29, 2024 at 16:26 #3266435

Bear-Faced Cow
Participant

It’s right there in the mixer tab…

jord

Jordan L. Chilcott

Web Site: https://jordanchilcottmusic.com/

1
Thanked by: Brad

Replied November 20, 2024 at 10:38 #3316246

Weathercade
Participant

I know this is an old thread but this may help someone.

I’ve had the same issue. In Reaper I ended up routing OHs to a non existent channel on my main drum track and loading another instance of ezd3 on a separate track with only cymbals no other drums or hats. It’s not CPU efficient but it completely avoids any unwanted bleed for mixes that has no bleed control.

You can then make a main drum bus to group it all together.

EZdrummer version: 3.0.6
Operating system: Windows 11
Author

Replies

Viewing 8 replies - 1 through 8 (of 8 total)

Removing bleed from OHs

EZdrummer Help

Viewing 8 replies - 1 through 8 (of 8 total)